Feeds:
Posts
Comments

Posts Tagged ‘Marbling Tutorial’

Welcome Back

After sharing a picture of my first marbled print. I wondered if you would like to see how the print was created? For this tutorial I used the Marbling 4 Fun kit that I reviewed in an earlier post.

My first marbled pages

My first marbled pages

Here is the Marbling 4 Fun video tutorial, for mixing up the floater powder. You need to do this 24 hours before you want to marble, for the mix to set. This is the fluid that the paints float upon.

Because I only had a small bowl to mix in and a small bottle to store it in, I used the guide found on the Marbling 4 Fun website that states : 5 grams of floater powder to 1 litre of water. I made up 1 litre of water to the 5 grams of floater powder and it was enough to fill the small tray that the kit comes with. So you don’t need so much storage space if you are only doing small items.

To store my floater mixture; I used a clean and empty 2 litre plastic milk bottle, which has a screw top lid. Write on the bottle what it will contain BEFORE you fill it, to ensure there are no accidents with people trying to drink it! You need to leave the mixture at room temperature overnight before you use it. After this stage, if stored in the screw top bottle in the fridge, it can last up to three months.

Set up you area to marble in.

This is a messy process, I won’t lie, but its also very much worth it. The floater mixture, leaves a coating of what feels like thinned out hair gel, on the surface of the paper/project and it takes a fair while to dry. So you need to plan for where you will put them. Here’s how I set up the area I marbled in.

Preparing your workspace to marble in.

Preparing your workspace to marble in.

First I put a layer of plastic over the whole area, these are just bin bags cut along the sides so they lie flat. On the right, you can see a few layers of blank newsprint, this is not expensive and I got mine from a house moving company. This paper is to lie wet pages onto, while they dry. In the end I also added a try under the white box so I had somewhere to put wet tools.

You need to mix the paint in the kit with soft water 1:1. As suggested by the company, I used old camera film pots for the mixed paint and secured them to the sides of the lid of the box, with masking tape. Its worth sticking them down as by the time you put the pipettes in, they fall over without support! (Ask me how I know!)

Its a good idea to work on a hard floor in case of drips n spills and expect to leave the wet papers overnight if you are working in cold conditions. This was done in February in the UK and they took around 12-24 hours to dry depending on the size of the card/paper, in the unheated studio. Have a bucket to hand to dump the wet waste paper into.

Making marbled patterns

Stage 1: Applying the paint to the tray.

Here are the paints on the water, before I pulled the print.

My first marbling page. Paints on the water.

My first marbling page. Paints on the water.

To create this pattern I used;

  • One drip of Violet paint in each corner of the box
  • One drip of black paint into the centre of the purple shapes
  • White paint acts like a resist, I put white paint in the centre of the black circles
  • Another drip of purple into the centre of each of the shapes.

Using the star flower technique, I used a pin to drag ‘petals’ in to the centre of each shape; the flowers with the points, I created by pulling the paint back out toward the edges from each of the purple ‘petals’. I’ll add the star flower video tutorial at the end of the article.

Stage 2: Creating the print

Using 80 gsm printer paper, I placed a sheet on top of the pattern in the try, allowed it to sit there a few moments, then carefully peeled it back off to reveal the print. The first generation of print will be bright, the later ones more pastel.

Here are the newly printed pages, still wet with the floater mix.

First generation marbled paint print on the left and the second generation on the right.

First generation marbled paint print on the left and the second generation on the right.

Stage 3: The Finished prints

Here’s how the pages turned out after drying.

My first marbled pages

My first marbled pages

My second marbled page. Second generation of paint.

My second marbled page. Second generation of paint.

Links

Here is Craig Joubert’s video for how the flower pattern is created. I’ll try to make my own videos with marbling, once the light levels improve in the UK. Craig is the maker of the kit and the man behind Marbling 4 Fun.

Have you ever tried marbling? How did you get on? Would you like to see more marbling videos at a later date? Let me know in the comments below.

Best wishes and thanks for reading, see you soon

Billie :)

Read Full Post »

Follow

Get every new post delivered to your Inbox.

Join 264 other followers